您当前位置:首页 > 产品中心 > PTFE油封
PTFE油封J型
  • 代码:J型油封
  • 温度℃:-20/+200
  • 材料:聚四氟乙烯(PTFE)
  • 介质:
  • 应用:
  • 运动方式:
服务热线:021-68195112
产品详情

全PTFE油封的J型油封 

Different type of (all) PTFE oil seals.(PTFE) 



形式 

Type 

运转条件 

Rotary Condition 

主要性能与应 

用Main Performance and Application 


 

A型 

速度 Speed:30m/s
压力 Pressure:5bar 

全铁氟龙单密封唇,摩擦阻力小,
适于风车、泵、压缩机、齿轮箱、引擎曲轴箱等各种应用。
Single lip teflon seal,low friction, suitable for windmill,pump,compressor,gearbox,engine bearing and other applications. 


 

B型 

速度 Speed:18m/s
压力 Pressure:30bar 

全铁氟龙双密封唇,适用压力高达30bar,
适用于油压马达,泵,液压油压元件等应用。
Double lip teflon seal,use in high pressure 30bar,application in hydraulic motor,pump,hydraulic oil presses. 


 

C型 

速度 Speed:8m/s
压力 Pressure:3.5bar 

单密封唇弹力加强型,适用于
转轴圆度不佳或偏摆较大的旋转密封。
 Flexibility reinforced single lip,suitable for poor roundness and largely swung rotary shaft sealing. 


 

D型 

速度 Speed:8m/s
压力 Pressure:3.5bar 

与C型相同,但增加圆周密封,可应用于多粉尘环境。
Same as type C,but added circumferential seal,can be used in heavy dust environment. 


 

E型 

速度 Speed:30m/s
压力 Pressure:5bar 

与A型相同,但增加圆周密封,可应用于多粉尘环境。
Same as A,but added circumferential seal,can be used in heavy dust environment. 


 

F型 

速度 Speed:18m/s
压力 Pressure:30bar 

与B型相同,但增加圆周密封,可应用于多粉尘环境。
Same as type B,but added circumferential seal,can be used in heavy dust environment. 


 

I型 

速度 Speed:20m/s
压力 Pressure:5bar 

密封唇压力较高,适用于气体及磨耗性流体。
Sealing lip can resist high pressure,apply in gas and abradability fluid. 


 

J型 

速度 Speed:30m/s
压力 Pressure:1.5bar 

密封唇压力较低,主要应用于轴承的密封。
Low pressure-resistant,mainly apply in bearing sealing. 


 

H型 

速度 Speed:8m/s
压力 Pressure:20bar 

单密封唇V形弹簧加强,适用于转轴圆度不佳或偏摆较大的密封。
Single lip with "V" spring reinforced,suitable for poor roundness and largely swung rotary shaft sealing. 




 

PTFE油封材质选用 

Material Selection for PTFE Oil Seals 

编号 No. 

密封件材 

 Material 

应用特性 

Application Feature 

1 

纯铁氟龙 Virgin PTFE 

适用于食品,制药等制程
Suitable for foodstuff and pharmaceutical process. 

2 

玻纤填料铁氟龙PTFE filled glass fiber 

改良的耐压,耐磨性,抗化学性;较优的热导性
Improved pressure-resistant, wear resistance, excellent chemical resistance and optimum thermal conductivity. 

3 

青铜填料铁氟龙PTFE filled bronze 

耐高压,耐磨耗,热传导性佳,特别适用于190℃以上的高温场合
High pressure resistance, good thermal conductivity, abrasion 
resistance, especially for applications in high temperature above 190 ℃. 

4 

石墨填料铁氟龙PTFE filled graphite 

适用于短期无润滑或长期润滑不良的旋转应用
Suitable for Short-term without lubrication or long-term bad 
lubrication rotary applications. 

5 

碳纤填料铁氟龙PTFE filled carbon fibre 

耐磨,耐压性,良好热导性,低透气性
Excellent wear resistance and pressure resistance, good thermal conductivity,low-permeability 


 

钢环及静止密封垫材质选用 

Steel ring and static gasket material selection 

编号 No. 

钢环材 

质Material 

应用特性 

Application Feature 

1 

碳钢Carton steel 

标准材质,一般环境下润滑油或润滑脂之应用
Standard material, suitable for general environment of lubricating oil or grease. 

2 

304不锈钢304 stainless steel 

腐蚀环境下润滑油或润滑脂之应用
Suitable for lubricating oil or grease under corrosive environment. 

3 

316不锈钢316 stainless steel 

腐蚀性流体之密封
Corrosive fluid seal 

编号 No. 

密封垫材质Material 

应用特性Application Feature 

1 

NBR 

标准材质,一般环境下润滑油或润滑脂之应用,适用温度-40~100℃
Standard material, suitable for general environment of lubricating oil or grease,  applicable temperature - 40 ~ 100  

2 

FKM(Viton) 

高温下润滑油或润滑脂之应用,适用温度-20℃~200℃
Suitable for lubricating oil or grease under high temperature,
applicable tempreature - 20 ℃ ~ 200 ℃ 


 

转轴与沟槽的要求 

Requirements of shaft and groove 

     为充分发挥PTFE油封的优异性能与耐用性,并避免安装不当导致密封件受损,轴的密封面与密封件沟槽必须有适当的加工。安装时,聚四氟乙烯密封唇必须向压力侧。

 

 

Shaft 

 

■轴表面硬度≧40HRC(润滑不良或高速运转的场合≧58HRC) 

Shaft surface hardness≧40HRC 

(poor lubrication or high speed occasion≧  58HRC) 

■表面研磨并抛光以去除锐角,表面粗度Ra=0.2~0.5  um, 

真空应用Ra≦0.2um 

Grinding and polishing the surface to remove the sharp angle, 
the surface roughness Ra=0.2~0.5 um,vacuum applications   Ra≦0.2um 

■轴径尺寸公差h11   Shaft dimensional tolerances h11 

■端面导角15° - 30°     Face conduction angle 15° to 30° 

沟槽Groove 

■表面粗度Ra≦0.8um  Surface roughness Ra≦0.8um 

■沟槽尺寸公差H8  Groove dimensional tolerances H8 

■端面导角5° - 15°   Face conduction angle 5° to 15° 


 

PTFE油封的标准尺寸(参选用) 

Standard size of PTFE oil seal(Reference only) 

轴径*外径*宽度(mm) 

diameter of axle* outer diameter*width(mm) 

8*22*7~12 

20*35*7~12 

35*62*8~12 

70*100*10~12 

8*24*7~12 

20*40*7~12 

38*55*8~12 

72*95*10~12 

8*26*7~12 

20*47*7~12 

38*58*8~12 

75*95*10~12 

9*22*7~12 

22*32*7~12 

38*62*8~12 

75*100*10~12 

9*24*7~12 

22*35*7~12 

40*52*8~12 

80*100*10~12 

9*26*7~12 

22*40*7~12 

40*55*8~12 

80*110*10~12 

10*22*7~12 

22*47*7~12 

40*60*8~12 

85*110*10~12 

10*24*7~12 

24*35*7~12 

40*62*8~12 

85*120*10~12 

10*26*7~12 

24*37*7~12 

42*55*8~12 

90*110*10~12 

12*22*7~12 

24*40*7~12 

42*60*8~12 

90*115*10~12 

12*24*7~12 

24*47*7~12 

42*62*8~12 

90*120*12 

12*26*7~12 

25*35*7~12 

42*72*8~12 

95*115*12 

12*28*7~12 

25*40*7~12 

45*60*8~12 

95*120*12 

12*30*7~12 

25*42*7~12 

45*62*8~12 

100*120*12 

14*24*7~12 

25*45*7~12 

45*65*8~12 

100*125*12 

14*28*7~12 

25*47*7~12 

48*65*8~12 

100*130*12 

14*30*7~12 

25*52*7~12 

50*68*8~12 

100*135*12 

14*35*7~12 

26*37*7~12 

50*70*8~12 

105*130*12 

15*26*7~12 

26*42*7~12 

50*72*8~12 

110*130*12 

15*30*7~12 

26*47*7~12 

50*75*8~12 

110*140*12 

15*32*7~12 

28*40*7~12 

50*80*8~12 

115*140*12 

15*35*7~12 

28*47*7~12 

52*72*8~12 

115*150*12 

16*28*7~12 

28*52*7~12 

55*72*8~12 

120*150*12 

16*30*7~12 

30*40*7~12 

55*75*8~12 

125*150*12 

16*32*7~12 

30*42*7~12 

55*80*8~12 

125*160*12 

16*35*7~12 

30*45*7~12 

60*75*8~12 

130*160*12 

17*28*7~12 

30*47*7~12 

60*80*8~12 

YS25*42*10 

17*30*7~12 

30*50*7~12 

60*85*8~12 

YS28*42*10 

17*32*7~12 

30*52*7~12 

62*80*8~12 

YS35*56*12 

17*35*7~12 

32*45*8~12 

65*80*8~12 

YS36*52*10 

17*40*7~12 

32*47*8~12 

65*85*8~12 

YS40*56*10 

18*30*7~12 

32*52*8~12 

65*90*10~12 

YS40*58*12 

18*32*7~12 

35*47*8~12 

65*100*10~12 

YS40*52*10 

18*35*7~12 

35*50*8~12 

68*90*10~12 

YS30*50*10 

18*40*7~12 

35*52*8~12 

68*100*10~12 

YS35*56*10 

20*30*7~12 

35*55*8~12 

70*90*10~12 

YS35*56*15 

20*32*7~12 

35*60*8~12 

70*95*10~12 

YS40*58*15 

■高度7~12之间高度不受限制  No limit for heitght from 7~12mm. 

■若需要其他规格尺寸请与我们联系。 Other specification, please contace us. 

 



如何贮存密封件?

密封件作为密封配件之一,在工业生产行业中应用广泛,且用量之大。有些企业都会储备些常用的密封件以备不需之需。让人担心的事就是密封件保存环境,而我们密封件告诉您……如何贮存密封件?如果密封件存储不好的话,就会造成密封件大量浪费。下面具体看一下密封件都有哪些贮存条件,才能更好地保存密封件。

1.png

一、避免高温

密封件的存放室温好在30℃以下,避免密封件产生高温老化;

二、避免空气、尘埃

密封件必须存放在密封包装内,避免和空气中的水分或尘埃接触;


三、避免强光照射

密封件必须避开强光照射,避免密封件被空气中臭氧侵蚀或提早老化。各种密封其性能影响因素是不同的,如机械密封(填料密封等)影响因素有温度、介质、磨损、所承受压力等。